Luftwaffe and Allied Air Forces Discussion Forum  

Go Back   Luftwaffe and Allied Air Forces Discussion Forum > Discussion > Luftwaffe and Axis Air Forces

Luftwaffe and Axis Air Forces Please use this forum to discuss the German Luftwaffe and the Air Forces of its Allies.

Reply
 
Thread Tools Display Modes
  #1  
Old 26th February 2005, 12:47
markojeras's Avatar
markojeras markojeras is offline
Senior Member
 
Join Date: Dec 2004
Location: Zagreb, Hrvatska
Posts: 114
markojeras is an unknown quantity at this point
Messerschmitt rivets

Can somebody please tell me what kind/size/DIN? rivets used Messerschmitt on Bf 108 and Me 109?

With best regards,

Marko
Reply With Quote
  #2  
Old 27th February 2005, 18:09
D.B. Andrus's Avatar
D.B. Andrus D.B. Andrus is offline
Senior Member
 
Join Date: Dec 2004
Location: Alba, TX, USA
Posts: 114
D.B. Andrus
Working by memory and subject to correction....

I believe 7mm is the rivet diameter used by MTT.

HTH,
D.B.
Reply With Quote
  #3  
Old 27th February 2005, 22:37
Zamex's Avatar
Zamex Zamex is offline
Junior Member
 
Join Date: Dec 2004
Location: Zavar, Slovakia
Posts: 22
Zamex
And what about Focke-Wulf 190 rivets?
__________________
Zamex
Reply With Quote
  #4  
Old 27th February 2005, 23:45
D.B. Andrus's Avatar
D.B. Andrus D.B. Andrus is offline
Senior Member
 
Join Date: Dec 2004
Location: Alba, TX, USA
Posts: 114
D.B. Andrus
Don't have specifics, but....

logic dictates same size for FW. Anyone?

HTH,
D.B.
Reply With Quote
  #5  
Old 27th February 2005, 23:59
John Manrho John Manrho is offline
Alter Hase
 
Join Date: Dec 2004
Location: Netherlands
Posts: 1,753
John Manrho will become famous soon enough
Rivert diameter?

D.B.

Do you mean that 7 mm rivets were used thru out a MTT a/c????. I can't imagine that. There must be more diameters used.

John.
Reply With Quote
  #6  
Old 28th February 2005, 00:17
D.B. Andrus's Avatar
D.B. Andrus D.B. Andrus is offline
Senior Member
 
Join Date: Dec 2004
Location: Alba, TX, USA
Posts: 114
D.B. Andrus
Dural skin only....

sorry, I should have stated such.

Best Regards,
D.B.
Reply With Quote
  #7  
Old 12th March 2005, 03:21
George Hopp's Avatar
George Hopp George Hopp is offline
Senior Member
 
Join Date: Dec 2004
Location: Ottawa, CA
Posts: 830
George Hopp
Luftwaffe rivets - specifically Bf109, Me262, Do335

For a reference on the diameter of German rivets vs. Western Allied rivets, try OKL Sonderbericht Nr. 39 of 15 Jan 45, entitled "Maßnahmen zur Kleinhaltung des Tragflügelwiderstandes im gegnerischen Flugzeugbau" which compared the resistance of Allied and German wings, and gave reasons why the resistance of German wings was greater. One reason given was that the German rivets had a greater diameter, 7mm vs. 4mm for the Allies. This required greater force to spread the rivet heads, and caused bowing of the skinning panels, and bending of ribs, etc.

The a/c specifically mentioned were the 109, 262, and 335 vs. the Spitfire, Mustang, and Tempest.
Reply With Quote
  #8  
Old 12th March 2005, 20:40
judyc judyc is offline
Member
 
Join Date: Jan 2005
Location: Hamilton Montana
Posts: 33
judyc
Rivets

Hi guys;

Most of the rivets for the fuselage and wing, for both the 109 and the 190, including the Dora were 7mm with some 9mm and on high stress areas, such as the wing root which is heavily riveted on the Fw 190, the sizes were 10 and 13mm.
I went over the Dora 13 recently during the restoration and painting process and measured the rivets. They are very consistent as stated above.
HTH
Cheers,
Jerry
__________________
Judy Crandall
Eagle Editions Ltd.
Reply With Quote
  #9  
Old 12th March 2005, 22:37
George Hopp's Avatar
George Hopp George Hopp is offline
Senior Member
 
Join Date: Dec 2004
Location: Ottawa, CA
Posts: 830
George Hopp
109F va. Spitfire IX rivets

Hi, Jerry and Judy, good to hear from you.

To check the rivet head sizes I went down to the Air Museum this morning and checked over the 109F and the Spitfire IX beside it. The problem with the 109F, of course, is that it has been restored, and so re-riveted. On one fuselage segment, I saw a line of 9mm rivets partially covered by filler, and beside it a nice line of 6mm rivets. Inboard on the wing, I got, close to the spar, heads between 8mm and 10mm; outboard I got mainly lines of 7mm heads. On the rear half of the wing I got lines of 8-9mm; but in many places, also lines of 6mm heads. On the lower cowling, 6mm; on the fin, 6.5mm; and on the horizontal stabilizer, 7mm. Under and behind the cockpit, 8mm; top of the wing radiator upper flap, 8mm; and on the top flap surface, 8.5mm. Olong the upper fuselage there were 8mm rivets along one stringer but 6mm ones along another.

On the Spitfire IX, the rivets were much more uniform. On the wing leading edge they were 8.5mm, but in all other areas they were about 5-6mm.

This pretty well agrees with the 1945 report.
Reply With Quote
  #10  
Old 13th March 2005, 10:28
ThomasA ThomasA is offline
Junior Member
 
Join Date: Dec 2004
Location: Sweden
Posts: 4
ThomasA
Rivet sizes

This thread makes me confused. Are you talking about the rivet head diameter here? Or the diameter of the rivet shaft? It is the shaft diameter which is the designated rivet diameter.

For clarity in technical terms:
The rivet diameter is the diameter of the rivet shaft. Reason: It is this part of the rivet which is the actual load carrying part. The rivet head and the crushed end is "just" holding the panels together. Also the visible countersunk rivet head can be machined after assembly in order to have an absolutely smoth surface in which case the visible rivet head diameter is changed. This does not apply to round headed rivets of course. Anohter problem is that there is something called oversized rivets. These are rivets which are slightly larger (~0,2-0,3mm) than nominal size rivets. They are used when you repair the structure and have to drill out old rivets. When a rivet is drilled out the hole normally becomes a little larger and therefore a slightly larger rivet is used.

I would guess that what you call 7mm rivets is actually 3,5mm rivets and 8,5mm is 5mm.

/Thomas Adamsson
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Me 262 Jagdverband Honor Goblet sponsored by Messerschmitt Augsburg Roger Gaemperle Luftwaffe and Axis Air Forces 4 17th July 2005 18:35
Messerschmitt Me 209V5/6 (A-1/2) Ruy Horta Luftwaffe and Axis Air Forces 8 8th July 2005 00:14
Monogram Messerschmitt O'Nine Gallery on ebay Alessandro Nati Fornetti Books and Magazines 0 20th June 2005 15:45
Messerschmitt Parts Drawings Question crawdad Luftwaffe and Axis Air Forces 0 10th May 2005 05:41
Falcon's Messerschmitt Bf 109 Hangar - (Photo Archive) Falcon Links 0 29th December 2004 23:07


All times are GMT +2. The time now is 11:32.


Powered by vBulletin® Version 3.7.2
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2018, 12oclockhigh.net